Description

Autoclave for sterilizing a wide variety of load types. 18-liter capacity, Class B, double safety lock, and USB port. Finished in a vibrant green color.

Programs:

Solid
Wrapped
Liquid
Textile
Prion
B&D Test
Helix Test
Vacuum test

Characteristics

Fully automatic with pre-programmed sterilization cycles.
Chamber and door in stainless steel, with electro-polished finish.
High-precision control system for perfect sterilization results.
User-friendly interface.
LCD screen, continuously displays information about the cycle process.
Open-type water tank. This feature makes filling and cleaning the tank easier. IMPORTANT: Do not reuse the water from the waste tank.
Optional printer (not included. Reference 922-PRINTER04 ).
Languages: Spanish, English, German, French, Italian, Portuguese, Dutch, Polish, Romanian, Czech, Latvian, Lithuanian, Hungarian and Chinese.

Security devices

Circuit breaker.
Protect the equipment from any possibility of power supply failure.
Action: Interrupt the power supply.
Thermal circuit breakers.
Protection against possible short circuits and possible overheating in the primary network of the transformer.
Action: Temporary interruption (until the temperature has dropped) in the winding.
Safety valve.
Protection against a possible increase in pressure inside the chamber.
Action: Steam release until a normal pressure level is restored.
Micro switch to control the door status.
It controls the door adjustment to start a sterilization cycle.
Action: Transmits the signal to alert about the incorrect position of the door.
Thermostat for the heating elements in the steam generator.
Protection against possible overheating of the heating elements in the steam generator.
Action: Interrupts the power supply to the heating elements in the steam generator.
Thermostat for the heating elements in the chamber.
Protection against possible overheating of the heating elements in the chamber.
Action: Interrupts the power supply to the heating elements in the chamber.
Automatic leveling of the hydraulic system.
The hydraulic system will return to its natural pressure if the sterilization cycle is manually interrupted.
Action: Internal pressure will be restored automatically.
Door lock
Effective protection to prevent accidental opening of the door.
Action: Prevents the door from opening using a hydraulic locking system.

Technical specifications:

Nominal Voltage: 220-240V; 50/60 Hz; 10A
Camera dimensions: 247 x 350 mm
Circuit breaker: F16A / 400V
Nominal Power: 2200VA
Sterilization temperature: 121 ºC / 134 ºC
Distilled water tank capacity: approx. 2.5 L
Operating temperature: 5 ºC / 40 ºC
Operating relative humidity: Max. 80%, non-condensing
External dimensions: 480 x 455 x 600 mm
Net Weight: 47 Kg
Maximum noise level: <70 dB
Atmospheric operating pressure: 76 / 106 kPa

Components:

Distilled water tank.
LCD screen.
Control Panel.
Main switch.
Tap for draining distilled and used water.
USB port.
Safety valve.
Ventilation grille.
Locking system.
Power cable.

Included accessories:

Instrument trays (3).
Base for trays.
USB flash drive.
Handle for removing the trays.
Door adjustment tool.
Drainage hoses (2).
Door seal.

Optional accessories and spare parts:

922-PRINTER04 Autoclave printer.

Autoclave process step by step:

1- Open the door, take the instruments and accessories inside the sterilization chamber, remove the wrapping and proceed to clean them.

2- Connect the power cord to a suitable power source.

3- Connect the printer ( optional accessory, sold separately. If you wish to purchase it, look for reference 922-PRINTER04 on this website ).

4- Power On: The main switch is located on the lower right front of the equipment.

Once activated, the LCD screen will light up, displaying the basic operating icons of the sterilizer, such as door position, water level, sterilization program, date, time, etc.

5- Fill the tank with distilled water.

Remove the top cover of the tank and proceed to fill it. If you hear a signal, it means you have exceeded the permitted water level in the tank. Please stop immediately and drain the necessary amount of water to turn off the signal.

6- Preparation of the material to be sterilized:

Place instruments made of different materials in separate trays, but be sure to separate them before sterilization.
If the instruments are not made of stainless steel, place sterilizing paper between the tray and the instruments.
Do not allow direct contact between instruments made of different materials.
Verify that all instruments are in the correct position.
Place instruments such as lenses, containers, tubes, etc. in the tray upside down, so that water does not stagnate inside them.
Do not overload the trays beyond their limit.
Do not stack the trays on top of each other, nor place them in direct contact with the wall of the sterilization chamber.
Do not use metal clips or pins, this may jeopardize the functioning of the sterilizer.

7- Select the sterilization program.

8- Start the sterilization cycle.

After selecting the sterilization program, place the instruments into the chamber using the trays and the supplied plastic handle.
Once the instruments are inside the chamber, proceed to close the door.
Caution: Make sure to close the door properly, otherwise the sterilizer will display an alarm and will not be able to start the program or will stop during the cycle.

9- Start the sterilization program.

Press the start button, then the sterilizer will start working for approximately 30-75 minutes.

10-Sterilization cycle completed.

Once the sterilization cycle is complete, the printer ( optional accessory with reference 922-PRINTER04 ) will automatically print the complete cycle report.
After the pressure drops to zero, you can open the door and remove the instruments. The sterilizer will alert you with an audible signal once the sterilization cycle is complete.
Caution: Whenever removing instruments, use the plastic handle supplied for the tray holder.

IMPORTANT: Do not reuse water from the waste tank.

Facility:

There must be at least 10 cm of free space around the sterilizer, 25 cm at the top, and enough space for the door to open completely.
The area where the sterilizer operates must have adequate ventilation.
The sterilizer should be placed on a weight-resistant table at a suitable level for handling.
Do not cover or block the side vents or the condenser fan air outlet grille.
Do not place the sterilizer near water sources where it may be splashed.
Keep it away from other heat sources.

Example of a printed report * :

* The printer is an optional accessory and is sold separately with reference 922-PRINTER04 .

================================
Program: WRAPPED
Temperature: 134C
Pressure: 206.0 kPa
Drying time: 08Min
Sterilization time: 4.0 min
--------------------------------
Time Temp. Pressure
Start 12:28:17 089.0C
T1: 12:31:32 087.1C -075.0kPa
T2: 12:33:43 110.2C 052.0kPa
T3: 12:36:37 088.9C -080.0kPa
T4: 12:39:20 114.7C 053.7kPa
T5: 12:43:37 087.9C -080.0kPa
T6: 12:50:40 134.8C 206.0kPa
TS: 134.7C 209.5kPa
Max. Temperature: 135.2C
Min. Temperature: 134.3C
Max. Pressure: 214.0kPa
Min. Pressure: 204.9kPa
T7: 12:54:39 134.4C 211.4kPa
T8: 12:57:36 102.1C -060.0kPa
T9: 12:59:54 098.2C -060.0kPa
End 13:04:07 102.4C
--------------------------------
Cycle No.: 00017
Result: success
Date: 2014-06-07
SN:E54723
Operator:
================================

Regulations:

93/42/EEC Medical Health Directive.
97/23/EEC Pressure Equipment Directive.
EN 13060 Small water steam sterilizers.
EN 61326, EN 61000 Electromagnetic compatibility.
EN 61010-1, UL 61010-1 Safety requirements.
EN 61010-2-040, IEC 61010-2-040 Specific requirements for steam sterilizers used for the treatment of medical materials.

18 liter class B green autoclave